manualshive.com logo in svg

Sharp AR M162 - B/W Laser - All-in-One, Operation Manual, Page: 8 / 372

Share
Download
Sharp AR M162 - B/W Laser - All-in-One Operation Manual Download Page 8

6

CAUTIONS

Follow the cautions below when using this machine.

CAUTIONS ON USING

Warning:

• The fusing area is hot. Exercise care in this area when removing misfed paper.
• Do not look directly at the light source. Doing so may damage your eyes.

Caution:

• Do not switch the machine rapidly on and off. After turning the machine off, wait 10 

to 15 seconds before turning it back on.

• Place the machine on a firm, level surface.
• When the machine is not used for a long time, for example, during prolonged 

holidays, turn the power switch off and remove the power cord from the outlet.

• When moving the machine, be sure to turn the power switch off and remove the 

power cord from the outlet.

• Do not cover the machine with a dust cover, cloth or plastic film while the power is 

on. Doing so may prevent heat dissipation, damaging the machine.

• Do not make any modifications to this machine. Doing so may result in personal 

injury or damage to the machine.

• Do not make copies of anything which is prohibited from copying by law. The 

following items are normally prohibited from printing by national law. Other items 
may be prohibited by local law.

• Money   • Stamps   • Bonds   • Stocks 
• Bank drafts   • Checks   • Passports   • Driver's licenses

• Do not touch the photoconductive drum. Scratches or smudges on the drum will 

cause dirty prints.

• Store spare toner cartridges in a cool dry place without removing from the package 

before use.

• If they are exposed to direct sunlight or excessive heat, poor copies may result.

"BATTERY DISPOSAL"

THIS PRODUCT CONTAINS A LITHIUM PRIMARY MEMORY BACK-UP BATTERY THAT MUST BE DISPOSED OF 
PROPERLY. PLEASE CONTACT YOUR LOCAL SHARP DEALER OR AUTHORIZED SERVICE REPRESENTATIVE FOR 
ASSISTANCE IN DISPOSING OF THIS BATTERY.

This product utilizes tin-lead solder, and a fluorescent lamp containing a small amount of mercury. 
Disposal of these materials may be regulated due to environmental considerations.
For disposal or recycling information, please contact your local authorities or the Electronics Industries Alliance: www.eia.org

Fusing unit

Summary of Contents for AR M162 - B/W Laser - All-in-One





















































































































































































































































































































































































Reviews:

No comments