manualshive.com logo in svg

Sharp AR M162 - B/W Laser - All-in-One, Operation Manual, Page: 315 / 372

Share
Download
Sharp AR M162 - B/W Laser - All-in-One Operation Manual Download Page 315

31

5

KEY OPERATOR PROGRAMS

The key operator programs allow the administrator of the machine (key operator) to enable and disable functions to 
suit the needs of the workplace. This chapter explains the key operator programs for the network and printer 
functions. For key operator programs for general use of the machine, see the "Key operator's guide".

KEY OPERATOR PROGRAM LIST

The key operator programs for the network and printer functions are shown in the following table. Factory default 
settings are indicated in bold. When "YES, NO" appears in the "Settings" column of a program, the program is 
enabled by pressing the [OK] key so that a checkmark appears in the checkbox. A checkmark in the checkbox (

) 

indicates that "YES" is selected. No checkmark (

) indicates that "NO" is selected.

For the initial key operator code set at the factory, see "PROGRAMMING A KEY OPERATOR CODE" in the "Key 
operator's guide".

The key operator programs that can be accessed depend on the machine and the options that are installed.

Mode

Program

Settings

Explanation

NETWORK

ENABLE DHCP

YES

, NO

Enable this setting if the machine will use an 
IP address that is assigned by a DHCP server. 
If DHCP is used, the IP address assigned to 
the machine may change automatically on 
occasion. If this happens, printing will not be 
possible. Change the port setting of the printer 
driver to the new IP address.

IP ADDRESS SETTINGS

• IP ADDRESS
• SUBNETMASK
• DEFAULT GATEWAY

–

If the machine will be assigned a permanent 
IP address, use these settings to enter the IP 
address, subnet mask, and default gateway.

☞

SPECIAL SETTINGS (page 33)

ENABLE TCP/IP

YES

, NO

Select whether or not TCP/IP protocol will be used.

ENABLE NetWare

YES

, NO

Select whether or not NetWare protocol will 
be used.

ENABLE EtherTalk

YES

, NO

Select whether or not EtherTalk protocol will 
be used.

ENABLE NetBEUI

YES

, NO

Select whether or not NetBEUI protocol will 
be used.

PRINTER

NOTICE PAGE

YES

, NO

Select whether or not a Notice Page 

(page 

36)

 is printed when printing is not successful 

due to a memory full (or other) error.

FORCED OUTPUT OF 
PRINT

YES, 

NO

When no tray has the specified size of paper, 
this setting is used to select whether or not 
the print job will be printed on the closest size 
of paper.

OUTPUT TRAYS

CENTER TRAY

,

UPPER TRAY

Specifies the output tray. When the printer 
driver is used to print, the setting in the printer 
driver has priority. (This setting is only 
available if a job separator tray is installed.)

Note

Summary of Contents for AR M162 - B/W Laser - All-in-One





















































































































































































































































































































































































Reviews:

No comments