Sharp AR M162 - B/W Laser - All-in-One Operation Manual Download Page 42

Page: 42 / 372

PERIPHERAL DEVICES AND
SUPPLIES

Optional equipment and supplies are explained in this chapter. To purchase optional equipment and supplies,
contact your dealer or SHARP service.

OPTIONAL EQUIPMENT

Convenient optional equipment can be installed on the machine as needed.

Yes: Can be installed.

No: Cannot be installed.

*1 The network expansion kit (AR-NB3) must be installed.
*2 The facsimile expansion kit (AR-FX11) must be installed.

• As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification

changes for product improvement without prior notice.

• Peripheral devices are normally optional, but are incorporated in some models as standard equipment.

AR-M162

AR-M207

Reversing single pass feeder (AR-RP6N)

Yes

Single pass feeder (AR-SP6N)

Yes

Document cover (AR-VR5)

Standard

Yes

250-sheet paper feed unit (AR-D24)

Yes

2 x 250-sheet paper feed unit (AR-D25)

Yes

Job separator tray kit (AR-TR4)

Yes

Dual function board (AR-EB9)

Yes

256MB expansion memory board (AR-SM5)

Yes

Facsimile expansion kit (AR-FX11)

Yes

8MB fax memory (AR-MM9)

Yes*

Network expansion kit (AR-NB3)

Yes

PS3 expansion kit (AR-PK1/N)

Yes*

Barcode font kit (AR-PF1)

Yes*

Flash memory kit (AR-PF2)

Yes*

Note

Summary of Contents for AR M162 - B/W Laser - All-in-One





















































































































































































































































































































































































Search results

Summary of Contents for AR M162 - B/W Laser - All-in-One

Reviews:

Sharp AR M162 - B/W Laser - All-in-One, Operation Manual, Page: 42 / 372

Search results

Summary of Contents for AR M162 - B/W Laser - All-in-One

Reviews: