Sharp AR M162 - B/W Laser - All-in-One Operation Manual Download Page 41

Page: 41 / 372

ADJUSTING THE DISPLAY CONTRAST

The contrast of the display can be adjusted as explained below.

Press the [SPECIAL FUNCTION] key.

The special function
screen will appear.

Select "DISPLAY CONTRAST" with
the [

] or [

] key.

Press the [OK] key.

The display contrast
adjustment screen will
appear.

Adjust the contrast with the [

] or [

]

key.

To reset the contrast to the
default setting, press the [C]
key.

Press the [SPECIAL FUNCTION] key.

You will return to the base
screen.

DUPLEX

SPECIAL FUNCTION

ACC.

DUPLEX SCAN
DUPLEX SCAN

SPECIAL FUNCTION

SPECIAL MODES

ORIG. SIZE ENTER
PAPER SIZE SET
DISPLAY CONTRAST

PQR

DUPLEX

SPECIAL FUNCTION

DUPLEX SCAN

SPECIAL FUNCTION
SPECIAL MODES
ORIG. SIZE ENTER
PAPER SIZE SET

DISPLAY CONTRAST

GHI

BACK

DISPLAY CONTRAST

SPECIAL FUNCTION

Summary of Contents for AR M162 - B/W Laser - All-in-One





















































































































































































































































































































































































Search results

Summary of Contents for AR M162 - B/W Laser - All-in-One

Reviews:

Sharp AR M162 - B/W Laser - All-in-One, Operation Manual, Page: 41 / 372

Search results

Summary of Contents for AR M162 - B/W Laser - All-in-One

Reviews: