manualshive.com logo in svg

Sharp AR M162 - B/W Laser - All-in-One, Operation Manual, Page: 266 / 372

Share
Download
Sharp AR M162 - B/W Laser - All-in-One Operation Manual Download Page 266

22

HOW TO USE THE NETWORK SCANNER FUNCTION

SELECTING A DESTINATION (USING THE [ADDRESS] 
KEY)

A destination can be selected using one of three methods: Selecting from "ADDRESS BOOK", using "ADDRESS 
ENTRY", or "ADDRESS SEARCH".

"ADDRESS BOOK"

1

Perform steps 1 to 6 of "BASIC 
TRANSMISSION PROCEDURE" (

page 20

).

2

Press the [ADDRESS] key.

The address selection 
screen appears

3

Press the [OK] key.

4

Change tabs as needed with the [

] or 

[

] key and select the desired 

destination with the [

] or [

] key.

• The [USER] tab changes as follows each time you 

press the [

] key:

[USER]

→

[ABCD]

→

[EFGHI]

→

[JKLMN]

→

[OPQRST]

→

[UVWXYZ]

→

[USER]

→

[ABCD]

→

...

To move backwards through the tabs, press the [

] 

key.

• You can switch between information on the selected 

destination and the destination list by pressing the 

 

key.

5

Press the 

 key.

A checkmark appears by the 
selected destination. To 
cancel the selection, press the 

 key once again to remove 

the checkmark.
To select multiple 
destinations, repeat steps 4 
and 5.

6

Press the [OK] key.

Multiple destinations can be 
selected for a Scan to E-mail 
transmission. (Maximum of 
20.)

Only one destination can be selected for a Scan to 
FTP or Scan to Desktop transmission.

7

Continue from step 9 of "BASIC 
TRANSMISSION PROCEDURE" (

page 21

).

8

OSURE

PAPER

ZOOM

AUTO %

OUTP

R MODE

GRAM

RESOLUTION
RESOLUTION

ADDRESS

FORMAT ORIGINA

ORIGINA

ADDRESS BROADCAST

 DESTINATION SELECT

ADDRESS BOOK

  ADDRESS ENTRY
  ADDRESS SEARCH

GHI

OK

BACK

        USER

PPD

  SALES
[#]:LIST  DETAIL
[ ]:SELECT ON/OFF

GH

PQR

DUPLEX

SPECIAL FUNCTION

DUPLEX SCAN

        USER

PPD

  SALES
  SUPPORT
[ ]:SELECT ON/OFF

Canceling transmission

• To cancel the transmission while 

"Reading" appears or before the 

 key is 

pressed, press the [C] or [CA] key.

• If the power is turned off or a power failure 

occurs while a document is being 
scanned in the SPF, the machine will stop 
and a document misfeed will occur. After 
the power is restored, remove the 
document as explained in "ORIGINAL 
MISFEED IN THE SPF" in "Operation 
manual (for general information and 
copier)".

@.-_

FUNCTION

ACC. #-C

READ-E

OK

Note

Summary of Contents for AR M162 - B/W Laser - All-in-One





















































































































































































































































































































































































Reviews:

No comments