Sharp AR M162 - B/W Laser - All-in-One Operation Manual Download Page 38 | Manualshive

Page: 38 / 372

Sharp AR M162 - B/W Laser - All-in-One Operation Manual Download Page 38

36

CHECKING THE TOTAL OUTPUT COUNT

To check the total number of pages output in copy, print, and fax modes and the total scan
count in scanner mode, hold down the [COPY] key when the machine is in the standby
state. The counts will appear while the key is held down. The total output count and the total
scan count can be used as a guideline for cleaning. When the total output count and the total
scan count exceed "999,999", the counts return to "0".

• An 11" x 17" or A3 page is counted as two pages.
• Each two-sided sheet that is output is counted as two pages. (An 11" x 17" or A3 sheet is counted as four

pages.)

• Blank copies and blank prints are included in the count.
• If the last page of a two-sided printing job is blank, it is not included in the count.

ON LINE DATA

PRINT

COPY

Note

«
...
36
37
38
39
40
...
»

Summary of Contents for AR M162 - B/W Laser - All-in-One





















































































































































































































































































































































































Reviews:

No comments