manualshive.com logo in svg

Sharp AR M162 - B/W Laser - All-in-One, Operation Manual, Page: 281 / 372

Share
Download
Sharp AR M162 - B/W Laser - All-in-One Operation Manual Download Page 281

37

4

CHECKING THE IP ADDRESS

There are several settings where the IP address must be entered or checked.  
To check the IP address of the machine, hold down the status button on the network expansion kit at least 2 
seconds to print out a Printer Setting List. 

How to reset the network expansion kit

To reset the network expansion kit, power on the machine while holding down the status button on the network 
expansion kit. 
Network scanner destination information and scanning settings will remain after the network expansion kit is 
reset, however, the network settings and network printer settings will revert to the factory default settings.

Status button

Caution

Summary of Contents for AR M162 - B/W Laser - All-in-One





















































































































































































































































































































































































Reviews:

No comments