R&S FSMR
TRACe Subsystem
1313.9723.12
6.1-231
E-1
TRACe<1|2>:IQ:DATA:MEMory[:RF]?
<offset samples>,<# of samples>
This command permits the readout of previously acquired (and frequency response corrected) I/Q
data from the memory, with indication of the offset related to the start of measurement and with
indication of the number of measurement values. Therefore a previously acquired data set can be
read out in smaller portions. The maximum amount of available data depends on the settings of
command TRACe:IQ:SET, the output format on the settings in the FORMat – subsystem.
The command requires that all requested measurement data be completely retrieved
before the device accepts any further commands.
If no baseband IQ data is available in the memory because the associated
measurement has not yet been started, the command generates a query error.
Parameter:
<offset samples>
Offset of the values to be output, referenced to the start
of the sampled data.
Value range: 0 ... <# of samples> - 1,
where <# of samples> is the value specified with the
TRACe:IQ:SET command
<# of samples>
Value range: 1 ... <# of samples> - <offset samples>
where <# of samples> is the value specified with the
TRACe:IQ:SET command.
Examples:
"TRAC:IQ:STAT ON"
'activates the I/Q data sampling
"TRAC:IQ:SET NORM,10MHz,32MHz,EXT,POS,100,4096"
'configures the
measurement:
'Filter type: Normal
'RBW: 10 MHz
'Sample Rate: 32 MHz
'Trigger Source: External
'Trigger Slope: Positive
'Pretrigger Samples: 100
'# of Samples: 4096
"INIT;*WAI"
‘
starts the measurement and waits for its end
"FORMat REAL,32"
‘
specifies the format of the response data
''Reading the results:
"TRAC:IQ:DATA:MEM? 0,2048"
''reads in 2048 I/Q values starting with the beginning of
the sampling
"TRAC:IQ:DATA:MEM? 2048,1024"
'reads in 2048 I/Q values starting with the beginning of
the sampling
"TRAC:IQ:DATA:MEM? 100,512"
'reads in 512 I/Q values starting with the trigger time
(<Pretrigger Samples> was 100))
Return values
Irrespective of the output format selected, the data is scaled linearly with 'V' as the unit and
corresponds to the voltage at the RF input of the device.
The return buffer is similarly configured to the return buffer with the TRACe:IQ:DATA? command
where all I data has the value 0.
Characteristics:
*RST value:
--
SCPI:
device-specific
Summary of Contents for FSMR
