R&S FSMR, Operating Manual, Page: 615 / 955

R&S FSMR CALCulate Subsystem
1313.9723.12 6.1-79 E-1
CALCulate<1|2>:MARKer<1 to 4>:FUNCtion:SUMMary:RMS:AVERage:RESult?
This command queries the result of the measurement of the averaged RMS value in the selected
measurement window. The query is only possible if averaging has been activated previously using
CALCulate<1|2>:MARKer<1 to 4>:FUNCtion: SUMMary:AVERage
.
The function is independent of the marker selection, i.e. the numeric suffix <1 to 4> of
:MARKer
is
irrelevant. It is only available in the time domain (span = 0).
A complete sweep with synchronization to sweep end must be performed between switching on the
function and querying the measured value to obtain a valid query result. This is only possible in single
sweep mode.
Example:
"INIT:CONT OFF"
'Switches to single-sweep mode.
"CALC:MARK:FUNC:SUMM:RMS ON"
'Switches on the function in screen A.
"CALC:MARK:FUNC:SUMM:AVER ON"
Swtiches on the average value
'calculation in screen A.
"INIT;*WAI"
'Starts a sweep and waits for the end.
"
CALC:MARK:FUNC:SUMM:RMS:AVER:RES?"
'Outputs the result of screen A.
Characteristics: *RST- value: -
SCPI: device-specific
This command is only a query and therefore has no *RST value.
CALCulate<1|2>:MARKer<1 to 4>:FUNCtion:SUMMary:RMS:PHOLd:RESult?
This command queries the result of the measurement of the RMS value with active peak hold in the
selected measurement window. The query is only possible only if the peak hold function has been
activated previously using
CALCulate<1|2>:MARKer<1 to 4>: FUNCtion:SUMMary:PHOLd
.
The function is independent of the marker selection, i.e. the numeric suffix <1 to 4> of
:MARKer
is
irrelevant. It is only available in the time domain (span = 0).
A complete sweep with synchronization to sweep end must be performed between switching on the
function and querying the measured value to obtain a valid query result. This is only possible in single
sweep mode.
Example:
"INIT:CONT OFF"
'Switches to single-sweep mode.
"CALC:MARK:FUNC:SUMM:RMS ON"
'Switches on the function in screen A.
"CALC:MARK:FUNC:SUMM:PHOL ON"
'Switches on the peak value
'measurement in screen A.
"INIT;*WAI"
'Starts a sweep and waits for the end.
"
CALC:MARK:FUNC:SUMM:RMS:PHOL:RES?"
'Outputs the result of screen A.
Characteristics: *RST- value: -
SCPI: device-specific
This command is only a query and therefore has no *RST value.
CALCulate<1|2>:MARKer<1 to 4>:FUNCtion:SUMMary:RMS:RESult?
This command queries the result of the measurement of the RMS power value in the selected
measurement window.
The function is independent of the marker selection, i.e. the numeric suffix <1 to 4> of
:MARKer
is
irrelevant. It is only available in the time domain (span = 0).
A complete sweep with synchronization to sweep end must be performed between switching on the
function and querying the measured value to obtain a valid query result. This is only possible in single
sweep mode.
Example:
"INIT:CONT OFF"
'Switches to single-sweep mode.
"CALC:MARK:FUNC:SUMM:RMS ON"
'Switches on the function in screen A.