Raisecom iTN2100 Hardware Description Download Page 97

Page: 97 / 312

Raisecom
iTN2100 (P100R002) Hardware Description

10 Ethernet access cards

Raisecom Technology Co., Ltd.

LED

Status

Description

LNK/ACT

(1–4)

Green

Link working LED



Green: the link interface is properly connected.



Off: the link interface improperly connected or disconnected.



Blinking green: the link interface is receiving or sending data.

10.4.5 DIP swtiches

Table 10-19 lists configurations of DIP switch SW1 on the OPCOM3500E-4FX.

Table 10-19

Configurations of DIP switch SW1 on the OPCOM3500E-4FX

DIP

switch

Function

Status

Description

Bit1

Bit2

Bit3

Bit4

Optical interface

device

SW1

Set the type
of the
optical
interface
device.

OFF

SS13

OFF

SS15

OFF

SS23

OFF

SS25

The card is properly configured before leaving factory. Do not configure if not needed.

10.4.6 Specifications

Table 10-20 lists specifications of the OPCOM3500E-4FX.

Table 10-20

Specifications of the OPCOM3500E-4FX

Parameter

Value

Dimensions

25 mm (width) × 232 mm (depth) × 240 mm (height)

Weight

0.4 kg

Max. power consumption 12 W

Summary of Contents for iTN2100

























































































































































































































































































































Search results

Summary of Contents for iTN2100

Reviews:

Raisecom iTN2100, Hardware Description, Page: 97 / 312

Search results

Summary of Contents for iTN2100

Reviews: