manualshive.com logo in svg

Raisecom iTN2100, Hardware Description, Page: 55 / 312

Share
Download
Raisecom iTN2100 Hardware Description Download Page 55

Raisecom 
iTN2100 (P100R002) Hardware Description 

5 NMS card 

 

 

Raisecom Technology Co., Ltd. 

26 

 

5.1.4 Buttons 

There are two buttons on the iTN2100-NMS panel, as listed in Table 5-4. 

Table 5-4

 

Buttons on the iTN2100-NMS panel 

Button 

Name 

Status 

Description 

– 

Buzzer control 
button 

MUTE 

In this status, when an alarm is being 
generated, the buzzer is mute. You cannot 
change this status through software. 

RING 

In this status, when an alarm is being 
generated, the buzzer rings. You can shield 
this status through software. 

RST 

Reset button 

Bounced 

The card is working properly. 

Down 

You can press this button to reset the card. 

 

5.1.5 LEDs 

There are eight LEDs on the iTN2100-NMS panel, as listed in Table 5-5. 

Table 5-5

 

LEDs on the iTN2100-NMS panel 

LED 

Status 

Description 

PWR 

Green 

Power LED 

 

Green: the power supply is normal. 

 

Off: the power supply is abnormal. 

SYS 

Green 

System status LED 

 

Green: the system is working improperly. 

 

Off: the system is working improperly. 

 

Blinking green: the system is working properly. 

MAS 

Green 

Primary/Slave mode LED of the system clock 

 

Green: the system clock is primary. 

 

Off: the system clock is slave. 

ALM 

Red 

Alarm LED 

 

Red: the communication fails or the clock fails. 

 

Off: there is no alarm on communication or clock. 

100M 

(SNMP) 

Green 

SNMP interface rate LED 

 

Green: the Ethernet rate is 100 Mbit/s. 

 

Off: the Ethernet rate is 10 Mbit/s. 

LNK/ACT 

(SNMP) 

Green 

SNMP interface working LED 

 

Green: the SNMP interface is working properly. 

 

Off: the SNMP interface is disconnected or is working 
improperly. 

 

Blinking green: the SNMP interface is receiving or 
sending data. 

Summary of Contents for iTN2100

























































































































































































































































































































Reviews:

No comments