Raisecom iTN2100 Hardware Description Download Page 117

Page: 117 / 312

Raisecom
iTN2100 (P100R002) Hardware Description

13 EOP cards

Raisecom Technology Co., Ltd.

13.2.4 LEDs

There are 8 LEDs on the OPCOM3500E-EOP3FE panel, as listed in Table 13-9.

Table 13-9

LEDs on the OPCOM3500E-EOP3FE panel

LED

Status

Description

PWR

Green

Power LED



Green: the power supply is normal.



Off: the power supply is abnormal.

SYS

Green

System status LED



Green: the system is working improperly.



Off: the system is working improperly.



Blinking green: the system is working properly.

100M

Green

Ethernet electrical interface 100 Mbit/s LED



Green: the Ethernet rate is 100 Mbit/s.



Off: the Ethernet rate is 10 Mbit/s or the connection fails.

LNK/ACT

(electrical
interface)

Green

Ethernet electrical interface working LED



Green: the Ethernet electrical interface is properly
connected.



Off: the Ethernet electrical interface is improperly connected
or disconnected.



Blinking green: the Ethernet electrical interface is receiving
or sending data.

Green

Optical interface input signal LED



Green: input signals are detected on the optical interface.



Off: no input signal is detected on the optical interface.

LNK/ACT

(1/2 optical
interface)

Green

1/2 optical interface working LED



Green: the 1/2 optical interface is properly connected.



Off: the 1/2 optical interface is improperly connected or
disconnected.



Blinking green: the 1/2 optical interface is receiving or
sending data.

13.2.5 Alarms

Table 13-10 lists alarms generated on the OPCOM3500E-EOP3FE.

Table 13-10

Alarms generated on the OPCOM3500E-EOP3FE

Alarm

Cause

Level

E1 LOS

Signals are lost.

Critical

E1 AIS

E1 signals are all 1 because the transmitted data is
incorrect or the remote device outputs AIS
signals.

Minor

Summary of Contents for iTN2100

























































































































































































































































































































Search results

Summary of Contents for iTN2100

Reviews:

Raisecom iTN2100, Hardware Description, Page: 117 / 312

Search results

Summary of Contents for iTN2100

Reviews: