Raisecom iTN2100 Hardware Description Download Page 83 | Manualshive

Page: 83 / 312

Raisecom iTN2100 Hardware Description Download Page 83

Raisecom
iTN2100 (P100R002) Hardware Description

10 Ethernet access cards

Raisecom Technology Co., Ltd.

54

10.1 iTN2100-16GF

10.1.1 Appearance and functions

Appearance

Function

The iTN2100-16GF is an Ethernet access card used by the iTN2100. It aggregates 16-way
1000 Mbit/s Ethernet services of the iTN2100.



Support up to 16-way GE services.



Support 802.1Q VLAN, QinQ, ACL, QoS, storm control, rate limiting, port mirroring,
link aggregation, Layer 2 protocol transparent transmission, and loopback detection.



Support IEEE 802.3ah OAM, IEEE 802.1ag, ITU-Y.1731, and extended OAM.



Support the GE Ethernet ring.



Support ITU-T G.8031 Ethernet linear protection switching.



Support ITU-T G.8032 Ethernet ring protection switching.



Support basic functions of MPLS-TP, static LSP configurations, and 128 bidirectional
LSPs.



Support L2VPN.



Support ALS.



Support ST, RSTP, and MSTP.



Support synchronous Ethernet.



RMON supports the statistics table, historical statistics configuration table, and
historical statistics table.



Support Digital Diagnostics Monitoring (DDM) of the Two-channel compact Small
Form-factor Pluggable transceiver (TSFP) module.



Support hot swapping.

«
...
81
82
83
84
85
...
»

Summary of Contents for iTN2100

























































































































































































































































































































Reviews:

No comments