Raisecom iTN2100 Hardware Description Download Page 240

Page: 240 / 312

Raisecom
iTN2100 (P100R002) Hardware Description

19 Multi-service cards

Raisecom Technology Co., Ltd.

211

19.2.3 Interfaces

Interface types

There are 3 interfaces on the OPCOM3500E-MULTI panel, as listed in Table 19-7.

Table 19-7

Interfaces on the OPCOM3500E-MULTI panel

Interface

Type

Description

VOICE

RJ45

One RJ45 interface outputs 4-way FXS/FXO voice
services.

2/4W

HDB26 female
connector

One HDB26 interface outputs 4-way 2/4W voice services.

DATA

HDB26 female
connector

One HDB26 interface outputs 4-way V.24/ RS485 data
services.

Interface parameters

Table 19-8 lists parameters of FXS/FXO interfaces on the OPCOM3500E-MULTI.

Table 19-8

Parameters of FXS/FXO interfaces on the OPCOM3500E-MULTI

Parameter

Description

Coding mode

A-law

Bit rate

64 Kbit/s

Impedance of audio interface



On-hook impedance: 2 MΩ



Off-hook loopback impedance: 200 Ω + 600 Ω//0.1 μF

Valid transmission
bandwidth

300 Hz–3400 Hz/600Ω

Gain frequency feature



RX (A/D) gain range: -3 dB to +13 dB



Default value: 0 dB



Step value: 0.1 dB



RX (D/A) gain range: -13 dB to +3 dB



Default value: -3.5 dB



Step value: 0.1 dB

Frequency distortion

< 0.5 dB (300 Hz–3000 Hz)

< 3.0 dB (3000 Hz–3400 Hz)

Total distortion (1020 Hz)

< 33 dB (0d Bm0 to -30 dBm0)

< (33–22) dB (-30 dBm0 to -40 dBm0)

< 22 dB (-40 dBm0 to -45 dBm0)

Variation of gain with input
level

Δ< 0.5 dB (+3 dBm0 to -40 dBm0)

Δ< 1.0 dB (-40 dBm0 to -50 dBm0)

Summary of Contents for iTN2100

























































































































































































































































































































Search results

Summary of Contents for iTN2100

Reviews:

Raisecom iTN2100, Hardware Description, Page: 240 / 312

Search results

Summary of Contents for iTN2100

Reviews: