Raisecom iTN2100 Hardware Description Download Page 149

Page: 149 / 312

Raisecom
iTN2100 (P100R002) Hardware Description

14 EOS cards

Raisecom Technology Co., Ltd.

120

14.2 OPCOM3500E-EOS-8FE

14.2.1 Appearance and functions

Appearance

Function

The OPCOM3500E-EOS-8FE is an 8-way electrical interface EOS tributary card on the
iTN2100.



Provide eight 10/100 Mbit/s Ethernet electrical interfaces.



Support assignment of eight ways of Ethernet services with bandwidth of N×VC12,
transmit them to the SDH network, and share bandwidth of 63 VC12.



Support two Ethernet encapsulation modes: GFP and LAPS.



Support VCAT and LCAS.



Support online software upgrade for local devices.



Support complete alarms and performance monitoring.



Support hot swapping.

14.2.2 Slots

The OPCOM3500E-EOS-8FE can be plugged into slots 1–5 and 8–12 on the iTN2100.

Summary of Contents for iTN2100

























































































































































































































































































































Search results

Summary of Contents for iTN2100

Reviews:

Raisecom iTN2100, Hardware Description, Page: 149 / 312

Search results

Summary of Contents for iTN2100

Reviews: