Raisecom iTN2100 Hardware Description Download Page 242

Page: 242 / 312

Raisecom
iTN2100 (P100R002) Hardware Description

19 Multi-service cards

Raisecom Technology Co., Ltd.

213

Parameter

Description

Degree of unbalance about
earth

> 40 dB (300 Hz–600 Hz)

> 46 dB (600 Hz–2400 Hz)

> 41 dB (2400 Hz–3400 Hz)

Idle-channel noise

< -67 dBm0

Feeding voltage (on-hook)

Typical -48 V

Feeding current

Typical 20 mA

Ring current voltage

Typical 60 V/30 Hz

Return loss

> 12 dB (300 Hz–600 Hz)

> 15 dB (600 Hz–3400 Hz)

Table 19-10 lists parameters of V.24 interfaces on the OPCOM3500E-MULTI.

Table 19-10

Parameters of V.24 interfaces on the OPCOM3500E-MULTI

Parameter

Description

Interface mode

DCE mode

Connector type

HDB26 female connector

Interface speed

The sampling frequency can be set to 64 KHz and 128 KHz.



64 KHz sampling frequency: 9.6 Kbit/s (maximum)



128 KHz sampling frequency: 19.2 Kbit/s (maximum)

Features

Comply with ITU-T V.24 recommendations.

Electrical feature

Comply with V.28 recommendations.

Transmission distance

15 m (standard recommendation for the serial port)

Table 19-11 lists parameters of RS485 interfaces on the OPCOM3500E-MULTI.

Table 19-11

Parameters of RS485 interfaces on the OPCOM3500E-MULTI

Parameter

Description

Connector type

RJ45

Sampling frequency

64 KHz/128 KHz

Interface speed



64 KHz sampling frequency: 9.6 Kbit/s (maximum)



128 KHz sampling frequency: 19.2 Kbit/s (maximum)

Compliance standard

Interface standards defined by RS485 AND RS422 protocols

Summary of Contents for iTN2100

























































































































































































































































































































Search results

Summary of Contents for iTN2100

Reviews:

Raisecom iTN2100, Hardware Description, Page: 242 / 312

Search results

Summary of Contents for iTN2100

Reviews: