Raisecom iTN2100 Hardware Description Download Page 79 | Manualshive

Page: 79 / 312

Raisecom iTN2100 Hardware Description Download Page 79

Raisecom
iTN2100 (P100R002) Hardware Description

9 Ethernet switching card

Raisecom Technology Co., Ltd.

50

9.1 iTN2100-PTU-4GE

9.1.1 Appearance and functions

Appearance

Function

The iTN2100-PTU-4GE is an Ethernet switching card to implement uplink GE service
switching on the iTN2100.



Support card-level protection and GE interface link aggregation between two cards.



Support master and secondary protection switching between two cards.



Support 24 GE switching capacity.



Support 802.1Q VLAN, Double TAG, ACL, QoS, storm control, rate limiting,
mirroring, link aggregation, layer 2 protocol transparent transmission, loopback
detection, etc.



Support IEEE 802.1ag and ITU-Y.1731.



Support GE ring network.



Support IEEE 802.3ah OAM.



Support layer 2 SLA.



Support Ethernet line protection according to ITU-T G.8031.



Support Ethernet ring network protection according to ITU-T G.8032.



Support statistics, historical configuration statistics, and historical statistics through
RMON.



Support DDM for the SFP module.



Support hot swapping.

9.1.2 Slots

The iTN2100-PTU-4GE can be plugged into slots 9 and 10 on the iTN2100. If you use only
one iTN2100-PTU-4GE, you must plug it into slot 9.

«
...
77
78
79
80
81
...
»

Summary of Contents for iTN2100

























































































































































































































































































































Reviews:

No comments