manualshive.com logo in svg

Raisecom iTN2100, Hardware Description, Page: 207 / 312

Share
Download
Raisecom iTN2100 Hardware Description Download Page 207

Raisecom 
iTN2100 (P100R002) Hardware Description 

15 PDH and RCMS cards 

 

 

Raisecom Technology Co., Ltd. 

178 

 

Interface 

Status 

Description 

LOS (A–D) 

LOS (1–4) 

Red 

Related nterface LOS alarm LED 

 

Red: input LOS alarms are generated on the related 
interface. 

 

Off: no input LOS alarms are generated on the related 
interface. 

 

Blinking green: input LOS alarms are generated on the 
remote device connected to the related interface. 

 

15.10.5 DIP switches 

Version A 

The OPCOM3500E-120H×4 (version A) has two DIP switches: SW6 and SW7, as listed in 
Table 15-54 and Table 15-54. 

Table 15-54

 

Configurations of DIP switch SW6 on the OPCOM3500E-120H×4 (version A) 

DIP 

switch 

Function 

Status 

Description 

Bit1 

Bit2 

Bit3 

Bit4 

Optical interface 

device 

SW6 

Set the type 
of the 
optical 
interface 
device. 

ON 

ON 

ON 

ON 

M 

ON 

ON 

ON 

OFF 

S1 

ON 

ON 

OFF 

ON 

S2 

ON 

ON 

OFF 

OFF 

S3 

ON 

OFF 

ON 

ON 

SS13 

ON 

OFF 

ON 

OFF 

SS15 

ON 

OFF 

OFF 

ON 

SS23 

ON 

OFF 

OFF 

OFF 

SS25 

 

 

SW6 is properly configured before the card leaves the factory. Do not configure it if 
not needed. 

Table 15-55

 

Configurations of DIP switch SW7 on the OPCOM3500E-120H×4 (version A) 

SW7 

Function 

Status 

Description 

DIP bit 

Bit1 

Enable or disable 

ON 

Enable ALS. 

Summary of Contents for iTN2100

























































































































































































































































































































Reviews:

No comments