manualshive.com logo in svg

Raisecom iTN2100, Hardware Description, Page: 124 / 312

Share
Download
Raisecom iTN2100 Hardware Description Download Page 124

Raisecom 
iTN2100 (P100R002) Hardware Description 

13 EOP cards 

 

 

Raisecom Technology Co., Ltd. 

95 

 

LED 

Status 

Description 

LNK/ACT 

Green 

Ethernet electrical interface working LED 

 

Green: the Ethernet electrical interface is properly connected. 

 

Off: the Ethernet electrical interface is improperly connected 
or disconnected. 

 

Blinking green: the Ethernet electrical interface is receiving 
or sending data. 

FDX 

Green 

Duplex mode LED 

 

Green: the Ethernet electrical interface works in full duplex 
mode. 

 

Off: the Ethernet electrical interface works in half duplex 
mode. 

 

13.4.5 Alarms 

Table 13-19 lists alarms generated on the OPCOM3500E-EOP-FE16E1. 

Table 13-19

 

Alarms generated on the OPCOM3500E-EOP-FE16E1 

Alarm 

Cause 

Level 

E1 LOS 

Signals are lost. 

Critical 

E1 AIS 

E1 signals are all 1 because the transmitted data is 
incorrect or the remote device outputs AIS 
signals. 

Minor 

E1 LOF 

Data sent by the upstream node is incorrect, 
because services are configured improperly or the 
hardware fails. 

Critical 

E1 CRC 

An Error on data during transmission. 

Critical 

E1 GID ERROR 

Reverse multiplexing configurations are 
incorrect. 

Critical 

E1 remote alarms (AIS, 
LOF, CRC, and LOS) 

The remote device managed by the card generates 
(AIS, LOF, CRC, and LOS) alarms. 

Critical 

E1 remote loopback 
alarm 

The remote device managed by the card generates 
a loopback. 

Critical 

Ethernet interface Link 
Down 

Links of Ethernet interfaces are disconnected. 

Critical 

 

13.4.6 Specifications 

Table 13-20 lists specifications of the OPCOM3500E-EOP-FE16E1. 

Summary of Contents for iTN2100

























































































































































































































































































































Reviews:

No comments