manualshive.com logo in svg

Raisecom iTN2100, Hardware Description, Page: 65 / 312

Share
Download
Raisecom iTN2100 Hardware Description Download Page 65

Raisecom 
iTN2100 (P100R002) Hardware Description 

7 SDH tributary cards 

 

 

Raisecom Technology Co., Ltd. 

36 

 

7.1 OPCOM3500E-STM1-S 

7.1.1 Appearance and functions 

Appearance 

Function 

 

The OPCOM3500E-STM1-S is an optical SDH tributary card on the 
iTN2100, with three versions: A, B, and C. 

 

Support SFP connectors for connecting fiber. 

 

Provide two SDH STM1 optical interfaces and support VC12. They 
support at most 63 VC12 channels if these two SDH STM1 optical 
interfaces are independent. 

 

Versions C provides 2 SDH STM1 optical interfaces and supports VC12 
and VC3. It supports at most 63 VC12 channels if these two SDH STM1 
optical interfaces are independent. 

 

These two SDH STM1 optical interfaces support 1+1 dual-optical interface 
protection, thus supporting inter-card protection if supported by the optical 
SDH aggregation card on the iTN2100. 

 

Support multiplexing section protection and channel protection. 

 

DCC channels support three modes: D1-D3, D4-D12, and D1-D12. This is 
supported by Version C only. 

 

The SDH optical interface supports local inner loopback and local outer 
loopback. 

 

Support ALS. 

 

Support LPR alarms on the remote device (if the remote device supports 
LPR alarms). 

 

Support hot swapping. 

 

Versions A and B can be distinguished by the hardware information 
label attached to the Print Circuit Board (PCB). 
The left figure is the the OPCOM3500E-STM1-S panel (versions A 
and  B)  and  the  right  figure  is  the  OPCOM3500E-STM1-S  panel 
(version C). 

 

7.1.2 Slots 

The OPCOM3500E-STM1-S can be plugged into slots 1–5 and 8–12 on the iTN2100. 

Summary of Contents for iTN2100

























































































































































































































































































































Reviews:

No comments