Raisecom iTN2100 Hardware Description Download Page 160

Page: 160 / 312

Raisecom
iTN2100 (P100R002) Hardware Description

14 EOS cards

Raisecom Technology Co., Ltd.

131

14.5 OPCOM3500E-8EOS-FX

14.5.1 Appearance and functions

Appearance

Function

The OPCOM3500E-8EOS-FX is an 8-way optical interface EOS service aggregation card
on the iTN2100.



Provide a way of 100 Mbit/s Ethernet optical interface.



Support virtual cascading of input Ethernet services with N×VC12 bandwidth, and then
transmit them to the SDH network.



Support two Ethernet encapsulation modes: GFP and LAPS.



Support VCAT and LCAS.



Support loopback detection, automatical switchoff and recovery of Ethernet interfaces.



Support storm control over broadcast messages, unknown multicast messages, and DLF
messages.



Support interface isolation protection.



Support interface aggregation.



Support QoS and determine four output queues by priority.



Support 802.1Q VLAN, support 4K concurrent VLANs, and support QinQ.



Support 8k MAC addresses and 30 static MAC addresses.



Support enabling or disabling MAC address learning based on interfaces.



Support configurable aging time ranging from 0s to 3825s. By default, it is 300s.



Support interface-based non-linear rate limiting ranging from 62 Kbit/s to 100 Mbit/s.



Support transparently transmitting BPDU, LACP, and 802.1x management frames.



Support remote NMS for RC500 and RC600 transceiver family.



Support hot swapping.

14.5.2 Slots

The OPCOM3500E-8EOS-FX can be plugged into slots 1–5 and 8–12 on the iTN2100.

Summary of Contents for iTN2100

























































































































































































































































































































Search results

Summary of Contents for iTN2100

Reviews:

Raisecom iTN2100, Hardware Description, Page: 160 / 312

Search results

Summary of Contents for iTN2100

Reviews: