Raisecom iTN2100 Hardware Description Download Page 50

Page: 50 / 312

Raisecom
iTN2100 (P100R002) Hardware Description

4 Power supplies

Raisecom Technology Co., Ltd.

LED

Status

Description

Cri

Red

Input voltage hierarchical alarm LED



Red: the deviation between the input voltage and the centered
voltage is within range 3.



Off: the deviation between the input voltage and the centered
voltage is beyond range 3.



You can set range 1, range 2, and range 3 but they must be between -100 V

and -240 V.



If input voltage hierarchical alarm LED is yellow or red, the input voltage is

within the allowed range.



If the alarm LED is yellow or red, the power supply is communicating with the

back plane and reporting power alarm status.

4.3.5 Specifications

Table 4-9 lists specifications of the SUB-PWRM-AC.

Table 4-9

Specifications of the SUB-PWRM-AC

Parameter

Value

Dimensions

38.5 mm (width) × 224 mm (depth) × 240 mm (height)

Weight

1.1 kg

Zero-load power
consumption

10 W

Rated power consumption

600 W

Table 4-10 lists input parameters of the SUB-PWRM-AC.

Table 4-10

Input parameters of the SUB-PWRM-AC

Parameter

Value

Nominal input voltage range

100–240 V

Rated input voltage

110 V/220 V

AC input frequency

47–63 Hz

Power consumption factor

0.95

Integrated equipment
efficiency

110 V input (full load)

80%

220 V input (full load)

80%

Summary of Contents for iTN2100

























































































































































































































































































































Search results

Summary of Contents for iTN2100

Reviews:

Raisecom iTN2100, Hardware Description, Page: 50 / 312

Search results

Summary of Contents for iTN2100

Reviews: