manualshive.com logo in svg

Raisecom iTN2100, Hardware Description, Page: 143 / 312

Share
Download
Raisecom iTN2100 Hardware Description Download Page 143

Raisecom 
iTN2100 (P100R002) Hardware Description 

13 EOP cards 

 

 

Raisecom Technology Co., Ltd. 

114 

 

13.9.6 Alarms 

Table 13-46 lists alarms of the iTN2100-EOT-GESTM4. 

Table 13-46

 

Alarms of the iTN2100-EOT-GESTM4 

Alarm 

Cause 

Level 

SFP absence alarm 

 

The SFP optical module is removed. 

 

The SFP optical module is improperly installed. 

 

The SFP optical module fails. 

Critical 

SFP sending failure 
alarm 

The SFP optical module fails. 

Critical 

RS-LOS alarm 

 

Attenuation of received signals is over great. 

 

The peer sender fails. 

 

The fiber head is unclean or the connector is 
improperly connected. 

 

The local receiver fails. 

Critical 

RS-LOF 

 

The TX clock of the peer device fails. 

 

Optical signals do not match. 

 

The local receiving referential clock fails. 

Critical 

RS-TIM 

 

The received trace byte of the local device and the 
sent trace byte of the peer device are inconsistent. 

 

Services are improperly configured. 

Critical 

AU-AIS 

 

The AU-AIS alarm of the VC4 channel is triggered 
by MS-AIS, R-LOS, R-LOF alarms. 

 

Services are improperly configured. 

 

The peer device sends AU-AIS alarms. 

 

The TX part of the peer device or the RX part of the 
local device fails. 

Minor 

AU-LOP 

 

The RX part of the peer device fails. 

 

Services are improperly configured on the peer 
device. 

 

BER of the local device is over great. 

Critical 

MS-EXC 

 

BER in the multiplexing section is over high. 

 

Optical signals are improperly transmitted. 

 

The performance of the local card is bad. 

Critical 

MS-AIS 

Multiplexing section alarm LED 

 

Alarm signals are inserted in the optical signals sent 
by the peer device. 

 

The peer device is a regenerator and receives LOS, 
LOF, or OOF alarms. 

Minor 

HP-LOM 

High order path LOM alarm 

 

Services are improperly configured. 

 

Byte H4 is lost or incorrect. 

Critical 

HP-TIM 

 

The received channel trace byte of the local device 
and the sent channel trace byte of the peer device are 
inconsistent. 

 

Services are improperly configured. 

Critical 

HP-PLM 

 

The received signal marking byte of the local device 
and the sent signal marking byte of the peer device 
are inconsistent. 

 

Services are improperly configured. 

Critical 

Summary of Contents for iTN2100

























































































































































































































































































































Reviews:

No comments