Raisecom iTN2100 Hardware Description Download Page 68

Page: 68 / 312

Raisecom
iTN2100 (P100R002) Hardware Description

7 SDH tributary cards

Raisecom Technology Co., Ltd.

Table 7-6

LEDs on the OPCOM3500E-STM1-S (Version C) panel

LED

Status

Description

PWR

Green

Power LED



Green: the power supply is normal.



Off: the power supply is abnormal.

SYS

Green

System status LED



Green: the system is working improperly.



Off: the system is working improperly.



Blinking green: the system is working properly.

LOF (1, 2)

Red

LOF alarm LED



Red: LOF alarms are generated on optical interfaces 1 and 2.



Off: no LOF alarms are generated on optical interfaces 1 and 2.

LOS (1, 2)

Red

LOS alarm LED



Red: LOS alarms are generated on optical interfaces 1 and 2.



Off: no LOS alarms are generated on optical interfaces 1 and 2.

7.1.5 Alarms

Table 7-7 lists alarms of the OPCOM3500E-STM1-S.

Table 7-7

Alarms of the OPCOM3500E-STM1-S

Alarm

Cause

Level

LOS alarm on the
STM1 optical
interface



Attenuation of received signals is over great.



The peer sender fails.



The connector of fiber is dirty or improperly connected.



The local receiver fails.

Critical

LOF alarm on the
STM1 optical
interface



The TX clock of the peer device fails.



Optical signals do not match.



The local receiving referential clock fails.

Critical

AU-AIS, AU-LOP The optical signals sent by the peer device is faulty and

the right pointer cannot be obtained.

Critical

haMS-EXC



BER in the multiplexing section is over high.



Optical signals are improperly transmitted.



The performance of the local card is bad.

Critical

MS-AIS

Multiplexing section alarm LED



Alarm signals are inserted in the optical signals sent by
the peer device.



The peer device is a regenerator and receives LOS,
LOF, or OOF alarms.

Minor

7.1.6 Specifications

Table 7-8 lists specifications of the OPCOM3500E-STM1-S.

Summary of Contents for iTN2100

























































































































































































































































































































Search results

Summary of Contents for iTN2100

Reviews:

Raisecom iTN2100, Hardware Description, Page: 68 / 312

Search results

Summary of Contents for iTN2100

Reviews: