Raisecom iTN2100 Hardware Description Download Page 72

Page: 72 / 312

Raisecom
iTN2100 (P100R002) Hardware Description

7 SDH tributary cards

Raisecom Technology Co., Ltd.

LED

Status

Description

SYS

Green

System status LED



Green: the system is working improperly.



Off: the system is working improperly.



Blinking green: the system is working properly.

LOF (1–4)

Red

LOF alarm LED



Red: input Loss of Frame (LOF) alarms are generated on
related optical interfaces.



Off: no input LOF alarms are generated on related
optical interfaces.

LOS (1–4)

Red

LOS alarm LED



Red: input Loss of Signal (LOS) alarms are generated on
related optical interfaces.



Off: no input LOS alarms are generated on related
optical interfaces.

7.2.5 Alarms

Table 7-12 lists alarms of the OPCOM3500E-4STM1-S.

Table 7-12

Alarms of the OPCOM3500E-4STM1-S

Alarm

Cause

Level

RS-LOS



Attenuation of received signals is over great.



The peer sender fails.



The connector of fiber is dirty or improperly connected.



The local receiver fails.

Critical

RS-LOF



The TX clock of the peer device fails.



Optical signals do not match.



The local receiving referential clock fails.

Critical

RS-TIM



The received trace byte of the local device and the sent
trace byte of the peer device are inconsistent.



Services are improperly configured.

Critical

AU-AIS



The AU-AIS alarm of the VC4 channel is triggered by MS-
AIS, R-LOS, R-LOF alarms.



Services are improperly configured.



The peer device sends AU-AIS alarms.



The TX part of the peer device or the RX part of the local
device fails.

Minor

AU-LOP



The RX part of the peer device fails.



Services are improperly configured on the peer device.



Bit Error Rate (BER) of the local device is over great.

Critical

MS-EXC



BER in the multiplexing section is over high.



Optical signals are improperly transmitted.



The performance of the local card is bad.

Major

Summary of Contents for iTN2100

























































































































































































































































































































Search results

Summary of Contents for iTN2100

Reviews:

Raisecom iTN2100, Hardware Description, Page: 72 / 312

Search results

Summary of Contents for iTN2100

Reviews: