Raisecom iTN2100 Hardware Description Download Page 234

Page: 234 / 312

Raisecom
iTN2100 (P100R002) Hardware Description

19 Multi-service cards

Raisecom Technology Co., Ltd.

205

19.1 OPCOM3500E-12MT

19.1.1 Appearance and functions

Appearance

Function

The OPCOM3500E-12MT is a 12-way magnetic telephone access card.



Provide 12-way magneto telephone interfaces.



Voice gain is adjustable. The step is set to 0.1 dB.



The RX A/D ranges from -10 dB to +16 dB. By default, it is set to 0 dB. The step value
is set to 0.1 dB.



The TX A/D ranges from -17 dB to +8 dB. By default, it is set to -3.5 dB. The step value
is set to 0.1 dB.



Support setting signaling types (a-bit and b-bit).



Support setting signaling modes (original signaling and reversed signaling).



The voice interface and ring current output provides overcurrent protection.



Support online upgrade.

Do avoid short-circuit during operation. If short-circuit occurs and the ring time is
over 10 minutes, the card will be damaged.

19.1.2 Slots

The OPCOM3500E-12MT can be plugged into slots 1–5 and 8–12 on the iTN2100.

Summary of Contents for iTN2100

























































































































































































































































































































Search results

Summary of Contents for iTN2100

Reviews:

Raisecom iTN2100, Hardware Description, Page: 234 / 312

Search results

Summary of Contents for iTN2100

Reviews: