manualshive.com logo in svg

Raisecom iTN2100, Hardware Description, Page: 212 / 312

Share
Download
Raisecom iTN2100 Hardware Description Download Page 212

Raisecom 
iTN2100 (P100R002) Hardware Description 

15 PDH and RCMS cards 

 

 

Raisecom Technology Co., Ltd. 

183 

 

15.11.3 Interfaces 

Interface types 

There are two interfaces on the OPCOM3500E-240H×2 panel, as listed in Table 15-61. 

Table 15-61

 

Interfaces on the OPCOM3500E-240H×2 panel 

Interface 

Type 

Description 

A, B 

1×9 optical interface 

 

Service downlink interface 

 

TX indicates sending and RX indicates receiving.

 

 

15.11.4 LEDs 

There are six LEDs on the OPCOM3500E-240H×2, as listed in Table 15-62. 

Table 15-62

 

LEDs on the OPCOM3500E-240H×2 

Interface 

Status 

Description 

PWR 

Green 

Power LED 

 

Green: the power supply is normal. 

 

Off: the power supply is abnormal. 

SYS 

Green 

System status LED 

 

Green: the system is working improperly. 

 

Off: the system is working improperly. 

 

Blinking green: the system is working properly. 

LPR (A, B) 

Red 

Optical interface A/B remote device LPR alarm LED 

 

Red: after the local device and the remote device connected 
to interface A or B are connected and work properly, LPR 
occurs on the remote device. 

 

Off: the remote device connected to interface A or B is 
working properly. 

LOS (A, B) 

Red 

Optical interface A/B/C/D LOS alarm LED 

 

Red: input LOS alarms are generated on interfaces A or B. 

 

Off: no input LOS alarms are generated on interface A or B. 

 

Blinking green: input LOS alarms are generated on the 
remote device connected to interface A or B. 

 

15.11.5 DIP switches 

The OPCOM3500E-240H×2 has two DIP switches: SW2 and SW3, as listed in Table 15-63 
and Table 15-64. 

Summary of Contents for iTN2100

























































































































































































































































































































Reviews:

No comments