manualshive.com logo in svg

Raisecom iTN2100, Hardware Description, Page: 278 / 312

Share
Download
Raisecom iTN2100 Hardware Description Download Page 278

Raisecom 
iTN2100 (P100R002) Hardware Description 

21 Cables 

 

 

Raisecom Technology Co., Ltd. 

249 

 

The 1000 Mbit/s crossover cable uses all 8 pins. The crossover is PIN1 to PIN3, PIN2 to 
PIN6, PIN4 to PIN7, and PIN5 to PIN8, as shown in Figure 21-7. 

 

Figure 21-7

 

Line order of the 1000 Mbit/s crossover cable 

Raisecom provides straight-through cables and 100 Mbit/s crossover cable which are different 
in name only. The straight-through cable is named as CBL-ETH-RJ45/RJ45-D while the 
crossover cable is named as CBL-ETH-RJ45/RJ45-X-D 

Table 21-3 lists technical specifications of the Ethernet cable. 

Table 21-3

 

Technical specifications of the Ethernet cable 

Item 

Description 

Color 

Dark grey 

Model 

Cat5 or later unshielded twisted pair cable (UTP-5/UTP-5e) or 
shielded twisted-pair cable (STP) 

Connector 

RJ45 connector 

Number of cores 

8 cores 

Length 

The letter D indicates the length, which is customized. For example, 
if the customer requires 2-meter cables, they are named CBL-ETH-
RJ45/RJ45-2m. 

 

Summary of Contents for iTN2100

























































































































































































































































































































Reviews:

No comments