Raisecom iTN2100 Hardware Description Download Page 241

Page: 241 / 312

Raisecom
iTN2100 (P100R002) Hardware Description

19 Multi-service cards

Raisecom Technology Co., Ltd.

212

Parameter

Description

Δ< 3.0 dB (-50 dBm0 to -55 dBm0)

Degree of unbalance about
earth

> 40 dB (300 Hz–600 Hz)

> 46 dB (600 Hz–2400 Hz)

> 41 dB (2400 Hz–3400 Hz)

Idle-channel noise

< -67 dBm0p

Feeding voltage (on-hook)

Typical -48 V

Feeding current

Typical 20 mA

Ring current voltage

Typical 60 V/30 Hz

Return loss

> 12 dB (300 Hz–600 Hz)

> 15 dB (600 Hz–3400 Hz)

Table 19-9 lists parameters of 2/4W interfaces on the OPCOM3500E-MULTI.

Table 19-9

Parameters of 2/4W interfaces on the OPCOM3500E-MULTI

Parameter

Description

Connector type

HDB26 female connector

Coding mode

A-law

Bit rate

64 Kbit/s

Impedance of audio interface



On-hook impedance: 2000 Ω



Off-hook loopback impedance: 200 Ω + 600 Ω//0.1 μF

Valid transmission
bandwidth

300 Hz–3400 Hz/600Ω

Gain frequency feature

RX (A/D) gain ranges from -11 to +19 dB. The default
value is set by the DIP switch.

TX (D/A) gain ranges from -24 to +7 dB. The default
value is set by the DIP switch.

Frequency distortion

< 0.5 dB (300 Hz–3000 Hz)

< 3.0 dB (3000 Hz–3400 Hz)

Total distortion (1020 Hz)

< 33 dB (0d Bm0 to -30 dBm0)

< (33–22) dB (-30 dBm0 to -40 dBm0)

< 22 dB (-40 dBm0 to -45 dBm0)

Variation of gain with input
level

Δ< 0.5 dB (+3 dBm0 to -40 dBm0)

Δ< 1.0 dB (-40 dBm0 to -50 dBm0)

< 0.5 dB (300 Hz–3000 Hz)

Summary of Contents for iTN2100

























































































































































































































































































































Search results

Summary of Contents for iTN2100

Reviews:

Raisecom iTN2100, Hardware Description, Page: 241 / 312

Search results

Summary of Contents for iTN2100

Reviews: