Raisecom iTN2100 Hardware Description Download Page 96

Page: 96 / 312

Raisecom
iTN2100 (P100R002) Hardware Description

10 Ethernet access cards

Raisecom Technology Co., Ltd.

10.4.3 Interfaces

Interface types

There are four interfaces on the OPCOM3500E-4FX panel, as listed in Table 10-16.

Table 10-16

Interfaces on the OPCOM3500E-4FX panel

Interface

Type

Description

1–4

1×9 optical interface



Each interface transmits one way of Ethernet
optical signals.



TX indicates sending and RX indicates receiving.

Interface parameters

Table 10-17 lists parameters of interfaces 1–4 on the OPCOM3500E-4FX.

Table 10-17

Parameters of interfaces 1–4 on the OPCOM3500E-4FX

Parameter

Description

Connector type

1×9 optical interface

Interface rate

100 Mbit/s

Maximum supported frame length

1632 Bytes

Flow control



Full duplex: IEEE 802.3x-based flow control



Half duplex: back-pressure flow control

10.4.4 LEDs

There are 10 LEDs on the OPCOM3500E-4FX panel, as listed in Table 10-18.

Table 10-18

LEDs on the OPCOM3500E-4FX panel

LED

Status

Description

PWR

Green

Power LED



Green: the power supply is normal.



Off: the power supply is abnormal.

SYS

Green

System status LED



Green: the system is working improperly.



Off: the system is working improperly.



Blinking green: the system is working properly.

(1–4)

Green

Optical signal detection LED



Green: optical signals are detected.



Off: no optical signals are detected.

Summary of Contents for iTN2100

























































































































































































































































































































Search results

Summary of Contents for iTN2100

Reviews:

Raisecom iTN2100, Hardware Description, Page: 96 / 312

Search results

Summary of Contents for iTN2100

Reviews: