Home
/
Raisecom
/
iTN2100
/
Hardware Description

Raisecom iTN2100, Hardware Description, Page: 211 / 312

Share

Page: 211 / 312

Raisecom iTN2100 Hardware Description Download Page 211

Raisecom
iTN2100 (P100R002) Hardware Description

15 PDH and RCMS cards

Raisecom Technology Co., Ltd.

182

15.11 OPCOM3500E-240H×2

15.11.1 Appearance and functions

Appearance

Function

The OPCOM3500E-240H×2 is a multi-service multiplexing tributary card on the
iTN2100.



Support 2-way PDH optical signal access and each way supports eight ways of E1
services.



Map at most 16 ways of E1 services on the office to the SDH signals.



Support complete alarms. Local alarms and remote alarms can be displayed
concurrently.



Support remote NMS for Raisecome's RCMS28XX Ethernet multiplexer family and
RC83XX optical transceiver family. If it is connected to the RCMS2811, they can
implement 1+1 inter-card protection switchover.



Support E1 local and remote loopback.



Support LPR alarms for remote devices.



Support ALS.



Support hot swapping.

15.11.2 Slots

The OPCOM3500E-240H×2 can be plugged into slots 1–5 and 8–12 on the iTN2100.

«
...
209
210
211
212
213
...
»

Summary of Contents for iTN2100

























































































































































































































































































































Reviews:

No comments