Raisecom iTN2100 Hardware Description Download Page 45 | Manualshive

Page: 45 / 312

Raisecom iTN2100 Hardware Description Download Page 45

Raisecom
iTN2100 (P100R002) Hardware Description

4 Power supplies

Raisecom Technology Co., Ltd.

16

4.2 SUB-PWRM-DC

4.2.1 Appearance and functions

Appearance

Function

The SUB-PWRM-DC is an intelligent 300 W DC power supply.



Provide power switch.



Provide 2:1 wide-range voltage: -36 V to -72 V.



P5 V rated output voltage per card.



Support hybrid input of AC and DC power.



Support hybrid input of intelligent and unintelligent power.



Support input reverse polarity protection (recoverable), input undervoltage
protection, input overvoltage protection, output overvoltage protection, output
current limit protection.



Support over temperature protection.



Support input surge current suppression.



Support in-position monitoring and fault reporting.



Support hierarchical alarms of input overvoltage and input undervoltage.



Support single-level alarms of output overvoltage and output undervoltage.



Support realtime reporting of power environment temperature



Support 1+1 hot backup.



Support hot swapping.

4.2.2 Slots

The SUB-PWRM-DC can be plugged into slots POWER1 and POWER2 on the iTN2100.

«
...
43
44
45
46
47
...
»

Summary of Contents for iTN2100

























































































































































































































































































































Reviews:

No comments