Raisecom iTN2100 Hardware Description Download Page 155

Page: 155 / 312

Raisecom
iTN2100 (P100R002) Hardware Description

14 EOS cards

Raisecom Technology Co., Ltd.

126

DIP

switch

Function

Status

Description

Bit1

Bit2

Bit3

Bit4

Optical interface

device

OFF

SS25

SW2 is properly configured before the card leaves the factory. Do not configure it if
not needed.

14.3.6 Alarms

Table 14-15 lists alarms of the OPCOM3500E-4EOS-4FX.

Table 14-15

Alarms of the OPCOM3500E-4EOS-4FX

Alarm

Cause

Level

Alarm overall alarm

TU-AIS, TU-LOP

Critical

Optical signal LOS

No optical signals are input.

Critical

Ethernet optical interface
link failure alarm



Fiber is disconnected.



The RX and TX of the remote device fail.

Critical

EOS AIS alarm



Services are improperly configured.



The channel to the peer device fails.



The cross connection module fails.

Minor

EOS LOP alarm



The interface between a tributary card and
the cross connection card fails.



Services are improperly configured.



Hardware fails.

Critical

Remote device LPR alarm

The remote transceiver is powered off.

Critical

14.3.7 Specifications

Table 14-16 lists specifications of the OPCOM3500E-4EOS-4FX.

Table 14-16

Specifications of the OPCOM3500E-4EOS-4FX

Parameter

Value

Dimensions

25 mm (width) × 232 mm (depth) × 240 mm (height)

Weight

0.4 kg

Max. power consumption 12 W

Summary of Contents for iTN2100

























































































































































































































































































































Search results

Summary of Contents for iTN2100

Reviews:

Raisecom iTN2100, Hardware Description, Page: 155 / 312

Search results

Summary of Contents for iTN2100

Reviews: