Raisecom iTN2100 Hardware Description Download Page 91

Page: 91 / 312

Raisecom
iTN2100 (P100R002) Hardware Description

10 Ethernet access cards

Raisecom Technology Co., Ltd.

10.3 iTN2100-2IGC

10.3.1 Appearance and functions

Appearance

Function

The iTN2100-2IGC is a 2-way 1000 Mbit/s Ethernet service access card, which must be
used together with the iTN2100-PTU-4GE to implement switching.



Provide two groups of GE interfaces (Combo interface, an optical interface and an
electrical interface in each group) for service access.



Support detection of dual-switching cards when working on the iTN2100 and support
cooperation with dual-switching cards.



Support selection of service channels on the backplane when working on the iTN2100.



Support saving, querying, and displaying manufacturing information.



Support management and maintenance of the SFP optical modules.



Support configuration and management of Ethernet optical interfaces.



Support saving and recovering configurations of a card, and preconfigurations of a card.



Support online software upgrade for the card.



Support hot swapping.

10.3.2 Slots

The iTN2100-2IGC can be plugged into slots 1–5, 8, and 10–12 on the iTN2100.

Summary of Contents for iTN2100

























































































































































































































































































































Search results

Summary of Contents for iTN2100

Reviews:

Raisecom iTN2100, Hardware Description, Page: 91 / 312

Search results

Summary of Contents for iTN2100

Reviews: