Raisecom iTN2100 Hardware Description Download Page 256

Page: 256 / 312

Raisecom
iTN2100 (P100R002) Hardware Description

20 Service aggregation cards

Raisecom Technology Co., Ltd.

227

Table 20-6

BITs 1–8 of the DIP switch

BIT

Status

Description

Default value

Enable failover.

OFF

Disable failover.

Enable ALS.

OFF

Disable ALS.

Reserved

OFF

Set to 2R mode and disable CDR.

OFF

Set to 3R mode and enable CDR.

Configure the speed manually.

OFF

Configure speed auto-negotiation.

6–8

OFF/OFF/OFF

Set the speed to 1000 Mbit/s Ethernet.

OFF/OFF/OFF

ON/OFF/OFF

Set the speed to 100 Mbit/s Ethernet.

OFF/ON/OFF

Set the speed to STM-4.

OFF/ON/ON

Set the speed to STM-1.

Other status

Reserved



By default, BITs 1

–8 of SW2, SW3, SW4, and SW5 are both set to OFF. It

means that failover and ALS are disabled and the card works in 2R mode (with
CDR being disabled).



Configurations on DIP switches are valid when they are powered on. After

configurations on DIP switches are changes, power them again to make new
configurations valid.



When BIT 4 is set to ON, BITs 5

–

8 are invalid.



When BITs 4 and 5 are set to OFF, BITs 6

–8 are invalid.



When BIT 4 is set to OFF and BIT 5 is set to ON, BITs 6

–8 are valid.

Before configuring DIP switching, you should confirm the attenuation value of the
fiber, ensuring the RX power of the line-side optical interfaces is in the specified
range. For details, see Table 20-2 Client-side interface metrics (optical modules),
Table 20-3 Client-side interface metrics (electrical modules), and Table 20-4 Line-side
interface metrics.

Configurations on DIP switches

Table 20-7 describes configurations on DIP switches of the iTN2100-Gb (A).

Summary of Contents for iTN2100

























































































































































































































































































































Search results

Summary of Contents for iTN2100

Reviews:

Raisecom iTN2100, Hardware Description, Page: 256 / 312

Search results

Summary of Contents for iTN2100

Reviews: