manualshive.com logo in svg

Raisecom iTN2100, Hardware Description, Page: 200 / 312

Share
Download
Raisecom iTN2100 Hardware Description Download Page 200

Raisecom 
iTN2100 (P100R002) Hardware Description 

15 PDH and RCMS cards 

 

 

Raisecom Technology Co., Ltd. 

171 

 

15.8.4 LEDs 

There are 20 LEDs on the OPCOM3500E-120FE×8L-GE panel, as listed in Table 15-44. 

Table 15-44

 

LEDs on the OPCOM3500E-120FE×8L-GE panel 

LED 

Status 

Description 

PWR 

Green 

Power LED 

 

Green: the power supply is normal. 

 

Off: the power supply is abnormal. 

SYS 

Green 

System status LED 

 

Green: the system is working improperly. 

 

Off: the system is working improperly. 

 

Blinking green: the system is working properly. 

1000M 

(GE) 

Green 

Ethernet interface 1000 Mbit/s LED 

 

Green: the Ethernet rate is 1000 Mbit/s. 

 

Off: the Ethernet rate is 100 Mbit/s or the connection fails. 

LNK/ACT 

(GE) 

Green 

Ethernet interface working LED 

 

Green: the Ethernet interface is properly connected. 

 

Off: the Ethernet interface is disconnected. 

 

Blinking green: the Ethernet interface is receiving or sending 
data. The blinking frequency is related to the transmission rate. 

LPR 

(1–8) 

Red 

Optical interface remote device LPR alarm LED 

 

Red: after the local device and the remote device connected to 
the related optical interface work properly, LPR occurs on the 
remote device. 

 

Off: the remote device connected to the related optical 
interface is working properly. 

LOS 

(1–8) 

Red 

Optical interface LOS alarm LED 

 

Red: input LOS alarms are generated on the related optical 
interface. 

 

Blinking red: the related optical interface receives signals 
properly while input LOS alarms are generated on the 
connected device   

 

Off: no input LOS alarms are generated on the related optical 
interface and connected remote device. 

 

15.8.5 Alarms 

Table 15-45 lists alarms generated on the OPCOM3500E-120FE×8L-GE. 

Summary of Contents for iTN2100

























































































































































































































































































































Reviews:

No comments