Raisecom iTN2100 Hardware Description Download Page 139

Page: 139 / 312

Raisecom
iTN2100 (P100R002) Hardware Description

13 EOP cards

Raisecom Technology Co., Ltd.

110

Interface Status

Description

LNK/ACT

(1–6)

Green

Link working LED



Green: the link interface is properly connected.



Off: the link interface improperly connected or disconnected.



Blinking green: the link interface is receiving or sending data.

13.8.5 Alarms

Table 13-40 lists alarms of the OPCOM3500E-HT-6FE24E1.

Table 13-40

Alarms of the OPCOM3500E-HT-6FE24E1

Alarm

Cause

Level

E1 AIS alarm

E1 signals are composed of "1" only,
because transmission fails or the peer
device outputs AIS signals.

Critical

E1 LOF alarm

The output data of uplink devices is
incorrect, because services are improperly
configured or hardware fails.

Critical

E1 CRC alarm

Data error occurs in transmission.

Critical

E1 GID ERROR alarm

Reverse duplexing is improperly
configured.

Critical

E1 remote loopback alarm

The remote device managed by the card
generates loopback alarms.

Critical

Ethernet interface link down
alarms

Alarms are generated due to Ethernet
interface link failure.

Critical

13.8.6 Specifications

Table 13-41 lists specifications of the OPCOM3500E-HT-6FE24E1.

Table 13-41

Specifications of the OPCOM3500E-HT-6FE24E1

Parameter

Value

Dimensions

25 mm (width) × 232 mm (depth) × 240 mm (height)

Weight

0.45 kg

Max. power consumption 12 W

Summary of Contents for iTN2100

























































































































































































































































































































Search results

Summary of Contents for iTN2100

Reviews:

Raisecom iTN2100, Hardware Description, Page: 139 / 312

Search results

Summary of Contents for iTN2100

Reviews: