Pontiac 2001 Montana Owner'S Manual Download Page 379

Page: 379 / 456

6-33

Headlamps

To replace he headlamp bulb(s) do the following:

1. Open the hood.

2. Remove the front turn signal/parking lamp assembly.

See “Front Turn Signal/Parking Lamps” later in
this section.

3. Remove the two wing nuts located on top of the

headlamp assembly.

4. Unscrew the black retainer ring that holds the bulb

assembly in place.

5. Pull the bulb assembly straight up from the

lamp housing.

6. Unhook the electrical connector by lifting up the

blue tabs and pulling the bulb out.

Summary of Contents for 2001 Montana








































































































































































































































































































































































































































































Search results

Summary of Contents for 2001 Montana

Reviews:

Brands by name

Popular brands

Pontiac 2001 Montana, Owner'S Manual

Search results

Summary of Contents for 2001 Montana

Reviews:

Brands by name

Popular brands