manualshive.com logo in svg

Pontiac 2001 Montana, Owner'S Manual

Share
Download
Pontiac 2001 Montana Owner'S Manual Download Page 339

5-26

NOTICE:

Do not place the jack under the rear axle 
control arms. Only use the areas shown for
proper jack location.

Do not raise the vehicle yet. Put the compact spare
tire near you.

CAUTION:

Getting under a vehicle when it is jacked up is
dangerous. If the vehicle slips off the jack, you
could be badly injured or killed. Never get under
a vehicle when it is supported only by a jack.

CAUTION:

Raising your vehicle with the jack improperly
positioned can damage the vehicle and even 
make the vehicle fall. To help avoid personal
injury and vehicle damage, be sure to fit the jack
lift head into the proper location before raising
the vehicle.

4. Attach the folding

wrench to the jack, and
turn the wrench
clockwise to raise the
jack head a few inches.

5. Raise the vehicle by turning the folding wrench

clockwise in the jack. Raise the vehicle far enough
off the ground so there is enough room for the spare
tire to fit under the wheel well.

Summary of Contents for 2001 Montana









































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands