manualshive.com logo in svg

Pontiac 2001 Montana, Owner'S Manual

Share
Download
Pontiac 2001 Montana Owner'S Manual Download Page 269

3-38

The following function is controlled by the primary
radio knob:

POWER

-

VOL: Push this knob twice to turn the rear

seat audio system on or off. ON or OFF will be
displayed for five seconds. The rear speakers will be
muted when the power is turned on. You may operate
the rear seat audio functions when the primary radio
power is off if the ignition is on.

The following functions are controlled by the rear seat
audio system buttons:

PWR: Press this button to turn the rear seat audio
system on or off. The rear speakers will be muted 
when the power is turned on. You may operate the 
rear seat audio functions even when the primary radio
power is off.

VOL: Press this knob lightly so it extends. Turn the
knob clockwise to increase volume and
counterclockwise to decrease volume. Push the knob
back into its stored position when you’re not using it.
The upper VOL knob controls the upper headphone and
the lower VOL knob controls the lower headphone.

AM FM: Press this button to switch between AM, FM1
and FM2. The display will show your frequency
selection. If the front passengers are already listening to
AM

-

FM, the rear seat audio controller will not switch

between the bands and cannot change the frequency.

SEEK: Press the up arrow to tune to the next higher
station and stay there. Press the down arrow to tune to
the next lower station and stay there. The display will
show your selection. The sound will mute while seeking.
The SEEK button is inactive if the AM FM mode on the
front radio is in use.

While listening to a cassette tape, press the up arrow to
hear the next selection on the tape. Press the down arrow
to go back to the previous selection. The SEEK button is
inactive if the tape mode on the front radio is in use.

While listening to a CD, press the up arrow to hear the
next selection on the CD. Press the down arrow to go
back to the start of the current selection (if more than
eight seconds have played). The SEEK button is inactive
if the CD mode on the front radio (if equipped) or the
CD changer is in use.

Summary of Contents for 2001 Montana









































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands