manualshive.com logo in svg

Pontiac 2001 Montana, Owner'S Manual

Share
Download
Pontiac 2001 Montana Owner'S Manual Download Page 264

3-33

To insert multiple discs do the following:

1. Turn the ignition on.

2. Press and hold the LOAD button for two seconds.

You will then hear a beep and the light, located to the
right of the slot, will begin to flash.

3. Once the light stops flashing and turns green, load a

disc. Insert a disc partway into the slot, label side up.
The player will pull the disc in.

Once the disc is loaded, the light will begin flashing
again. Once the light stops flashing and turns green
you can then load another disc. The disc player takes
up to six discs. Do not try to load more than six.

When a disc is inserted, the CD symbol will be
displayed. If more than one disc has been loaded, a
number for each disc will be displayed. If you select
an EQ setting for your disc, it will be activated each
time you play a disc.

If the radio is on or off, the last disc loaded will
begin to play automatically.

4. To load more than one disc but less than six,

complete Steps 1, 2 and 3. When you have finished
loading discs, with the radio on or off, press LOAD
to cancel the loading function. The radio will begin
to play the last CD loaded.

As each new track starts to play, the track number will
appear on the display.

Playing a Specific Loaded CD: For every CD loaded, 
a number will appear on the radio display. To play a
specific CD, first press the CD AUX button to start
playing a CD. Then press the numbered button that
corresponds to the CD you want to play. A small bar
will appear under the CD number that is playing, and the
track number will appear.

If CHECK CD appears on the radio display, it could be
due to one of the following conditions:
D The road is too rough. The disc should play when the

road is smoother.

D The disc is dirty, scratched, wet or upside down.
D The air is very humid. If so, wait about an hour and

try again.

If any error occurs repeatedly or if an error can’t be
corrected, please contact your dealer. If your radio
displays an error message, write it down and provide it
to your dealer when reporting the problem.

Summary of Contents for 2001 Montana









































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands