Home
/
Pontiac
/
2001 Montana
/
Owner'S Manual

Pontiac 2001 Montana, Owner'S Manual

Share

Page: 26 / 456

Pontiac 2001 Montana Owner'S Manual Download Page 26

1-14

7. If you have the 40/60 seat, attach the mini

-

buckle so

that the safety belt is ready for use when a passenger
uses the seat.

The buckle reattaches by pushing the latch into the
buckle until the red center pops out again.

Repeat these steps for the other section of the split
bench seat.

CAUTION:

A safety belt that is improperly routed, not
properly attached, or twisted won’t provide the
protection needed in a crash. The person wearing
the belt could be seriously injured. After
installing the seat, always check to be sure that
the safety belts are properly routed and attached,
and are not twisted.

Bucket Seats

If you have the rear bucket seats, the seatbacks can be
folded down or reclined. The seats can also be adjusted
forward or rearward and removed.

Folding or Reclining the Seatbacks

The seatback on a bucket seat can be either folded down
or reclined. The following explains how to use either the
nylon strap or the lever to fold or recline the seatback.

To fold down the seatback,
pull this nylon strap on the
rear of the seat.

To raise a seatback, pull the nylon strap while raising the
seatback until it locks upright.

«
...
24
25
26
27
28
...
»

Summary of Contents for 2001 Montana









































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands