manualshive.com logo in svg

Pontiac 2001 Montana, Owner'S Manual

Share
Download
Pontiac 2001 Montana Owner'S Manual Download Page 203

2-91

3. Using both hands, press the hand

-

held transmitter

button and the desired button on the HomeLink
Transmitter. Continue to press both buttons 
through Step 4.

4. Hold down both buttons until you see the indicator

light on the HomeLink Transmitter flash slowly and
then rapidly. The rapid flashing indicates that the
HomeLink Transmitter has been programmed.
Release both buttons once the indicator light starts to
flash rapidly.

If you have trouble programming the HomeLink
Transmitter, make sure that you have followed the
directions exactly as described. The HomeLink
Transmitter may not work with older garage door
openers that do not meet current Federal Consumer
Safety Standards. If you cannot program the transmitter
after repeated attempts, refer to “Rolling Code
Programming” later in this section or contact the
HomeLink Transmitter manufacturer 
at 1

-

800

-

355

-

3515.

Be sure to keep the original hand

-

held transmitter in

case you need to erase and reprogram the 
HomeLink Transmitter.

Canadian Owners: During programming, the
hand

-

held transmitter may automatically stop

transmitting after one or two seconds. In this case, you
should press and re

-

press the button on the hand

-

held

transmitter every two seconds without ever releasing the
button on the HomeLink Transmitter. Release both
buttons when the indicator light on the HomeLink
Transmitter begins to flash rapidly.

Summary of Contents for 2001 Montana









































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands