manualshive.com logo in svg

Pontiac 2001 Montana, Owner'S Manual

Share
Download
Pontiac 2001 Montana Owner'S Manual Download Page 210

2-98

Retro

-

Active Reset

Each of the two trip odometers has a feature called
retro

-

active reset. This feature can be used to set either

(or both) trip odometer(s) to the number of miles
(kilometers) driven since the ignition was last turned on.
This can be used if you forget to reset your trip
odometer at the beginning of a trip. To use the
retro

-

active reset feature, push and hold the trip/reset

button for at least three seconds. The trip odometer will
then display the number of miles (kilometers) driven
since the ignition was last turned on and you began
driving. (If you use the retro

-

active reset feature after

you have started the vehicle, but before you begin
moving, the display will show the number of miles
(kilometers) you drove during the last ignition cycle.)
Once you begin driving, the trip odometer will
accumulate mileage. For example, if you have driven
5.0 miles (8.0 km) since you started your vehicle, and
then activate the retro

-

active reset feature, the display

will show 5.0 miles (8.0 km). As you drive, the display
will then increase to 5.1 miles (8.2 km), 5.2 miles 
(8.4 km), etc. Only the trip odometer that is displayed
will be affected by the retro

-

active reset so that both trip

odometers can be used separately.

Tachometer

The tachometer displays the
engine speed in revolutions
per minute (rpm).

NOTICE:

Do not operate the engine with the tachometer in
the red area, or engine damage may occur.

Summary of Contents for 2001 Montana









































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands