manualshive.com logo in svg

Pontiac 2001 Montana, Owner'S Manual

Share
Download
Pontiac 2001 Montana Owner'S Manual Download Page 214

2-102

Anti-Lock Brake System Warning Light

The anti

-

lock brake

system warning light
should come on for a
few seconds when you
turn the ignition key 
to RUN.

If the anti

-

lock brake system warning light stays on longer

than normal after you’ve started your engine, turn the
ignition off. Or, if the light comes on and stays on when
you’re driving, stop as soon as possible and turn the
ignition off. Then start the engine again to reset the
system. If the light still stays on, or comes on again while
you’re driving, the anti

-

lock brake system needs service

and you don’t have anti

-

lock brakes. The brake pedal 

may be harder to push, or it may go to the floor. It may
take longer to stop. Adjust your driving accordingly.

The anti

-

lock brake system warning light should come

on briefly when you turn the ignition key to RUN. 
If the light doesn’t come on then, have it fixed so 
it will be ready to warn you if there is a problem.

Traction Control System Warning 
Light (Option)

United States

Canada

The traction control system warning light may come on
for the following reasons:
D If you turn the system off by pressing the TCS

button located in the center console switchbank the
warning light will come on and stay on. To turn the
system back on, press the button again. The warning
light should go off. See “Traction Control System” 
in the Index for more information.

D If there’s a brake system problem that is specifically

related to traction control, the traction control system
will turn off and the warning light will come on. 
If your brakes begin to overheat, the traction control
system will turn off and the warning light will come
on until your brakes cool down.

Summary of Contents for 2001 Montana









































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands