manualshive.com logo in svg

Nustep TRS 4000, Service Manual

Share
Download
Nustep TRS 4000 Service Manual Download Page 97

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

[email protected] - (800) 322-4434

89

Seat Mounting Bracket Assembly

Tools Required

5/32" hex key
Needle nosed pliers
½” socket and ratchet
Long socket extension
7/16" socket and ratchet
Torque wrench
242 Loctite

1. Remove seat assembly.  

See 

Seat Assembly Removal 

instructions.

2. Remove seat release bracket.

For S/N < 428341, see 

Seat Release Bracket 

instructions.

For S/N > 428342, see 

Seat Release Bracket With Stud 

instructions.

3. Swivel seat channel assembly 45

°°°°°

to access four bolts that attach seat
channel to seat.

 

 

4. Remove four bolts and washers.

 

42263 Seat Mounting Bracket Assembly 5-01-05

To avoid injury, and to ensure safe
operation of this product, fasteners
must be tightened to the proper torque.

!

 CAUTION

Summary of Contents for TRS 4000



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands