manualshive.com logo in svg

Nustep TRS 4000, Service Manual

Share
Download
Nustep TRS 4000 Service Manual Download Page 30

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

[email protected] - (800) 322-4434

Belt Idler Arm

Tools Required

Parts Required

Channel lock pliers

½” self locking ring

9/16" deep socket
2x4" block of wood
Hammer
Safety glasses

1. Remove covers.

See 

Cover Removal 

instructions.

2. Remove poly-v belt and sheave.

See 

Poly-V Belt & Sheave 

instructions.

3. Remove self-locking ring from
right side of idler arm shaft.

4. Remove belt idler arm from seat
rail assembly.

 

 

Ring will be destroyed during removal.

5. Transfer pulley.  Keep the
washer(s) on the side they were on.

6. Install belt idler arm.  Make sure
Nyliners don’t push out of holes.

 

 

42011 Belt Idler Arm 5-1-05

 

 

22

NOTE: This instruction applies only to units with S/N < 428326.

To avoid injury, wear safety glasses.

!

 CAUTION

Summary of Contents for TRS 4000



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands