manualshive.com logo in svg

Nustep TRS 4000, Service Manual

Share
Download
Nustep TRS 4000 Service Manual Download Page 36

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

[email protected] - (800) 322-4434

Flat Belt & Belt Idler Spring

42273 Flat Belt & Belt Idler Spring 5-1-05

28

NOTE: This instruction applies only to units with S/N > 428173.

Tools Required

5/16” wrench or nut driver
Measuring tape or yard stick
Safety glasses

1. Remove covers.  

See 

Cover Removal 

instruction.

2. Remove step through support assembly.  

See 

Step Through Support

instruction.

To avoid injury, wear safety glasses.

!

 CAUTION

4. Remove idler spring from flat belt clamp and right timing belt clamp.

3. Pull flat belt off front pulley.

Spring is under tension. To avoid injury,
or damage to the product, use caution
when removing or installing.

!

 CAUTION

Belt is under tension. To avoid injury, or
damage to the product, use caution
when removing or installing.

!

 CAUTION

Note: If replacing belt idler spring only, go
to step 8.

5. Remove timing belt clamp from right timing belt.

Summary of Contents for TRS 4000



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands