manualshive.com logo in svg

Nustep TRS 4000, Service Manual

Share
Download
Nustep TRS 4000 Service Manual Download Page 116

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

[email protected] - (800) 322-4434

Seat Release Lever

42093 Seat Release Lever 5-1-05

4. To install, do steps in reverse order.  Place Loctite on both bolts before
installing them, then tighten to 80 in-lbs.

Make sure
lever is
positioned
with flats
of lever
against the
bracket.

 

 

 

REFERENCE PHOTO:

80 inch-lbs

Torque Setting:

To avoid injury, and to ensure safe
operation of this product, fasteners
must be tightened to the proper torque.

!

 CAUTION

To avoid injury and prevent adverse
health effects, use Loctite in
accordance with the manufacturer’s
material safety data sheets, including
the use of safety glasses and
impermeable gloves. Material safety
data sheets are available via the
internet at 

www.loctite.com 

or by

calling Henkel Corporation at (800) 562-
8483.

!

 CAUTION

108

Summary of Contents for TRS 4000



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands