Nustep TRS 4000 Service Manual Download Page 83

Page: 83 / 130

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

[email protected] - (800) 322-4434

Footpedal Stabilizer 2000 (R or L)

Note: This only applies to units with serial numbers

≥

413368. For serial numbers 411001 –

413367, see Footpedal Support Tube 1999 instructions. Left side instructions are shown.

Tools Required

3/16" hex key
½” wrench
Snap ring pliers
Loctite 242
Large flat head screwdriver
Hammer
Grease/silicone (white or clear preferred)
Torque wrench
Safety glasses

1. Remove upper nut from stabilizer. Prevent shoulder bolt from turning.

2. Remove lower shoulder bolt from frame.

Shoulder bolt is locked to footpedal. Don’t
turn it. If it loosens, then Loctite it back in
during installation below.

Shoulder bolt is locked to rod end ball.
Remove rod end from shoulder bolt by
lightly tapping with a hammer.

42049 Footpedal Stabilizer 2000 5-01-05

To avoid injury, wear safety glasses.

CAUTION

Summary of Contents for TRS 4000



































































































































Search results

Summary of Contents for TRS 4000

Reviews:

Brands by name

Popular brands

Nustep TRS 4000, Service Manual

Search results

Summary of Contents for TRS 4000

Reviews:

Brands by name

Popular brands